维京征服重铸版-大幅增加流畅度、减少卡顿（强制DX7 & 战场人数降低）

雾雨 · 发表于 2016-3-29 08:32:15

标题 Title:
Viking Conquest Reforged - Greatly improve fps \ game performance by forcing Viking Conquest to use Direct X7 / DX7 and lowering the batthe size from 150 to 30
维京征服重铸版 - 大幅增加帧数、游戏性能，以强制使用Direct X7 / DX7和降低战场人数来实现

介绍 Introduction -
对不知道骑砍DX7模式的群众们 For people who don't know about Mount Blade's DX7 mode
(知道的请跳过该段落 If you know MB's DX7 then skip this paragraph)

在启动骑砍时，点击“配置” -〉“图像” -〉“渲染方式” 一项就可以变更DX7 / DX9。
When starting MB, click Configure-> Video -> Render Method, and you can change between DX7 / DX9 here.

如果你还没试过，现在就可以尝试一下DX７、看看他能让你的游戏变得多流畅（以及变流畅的代价——画质下降）
If you haven't done so before, try to apply DX7 and start the vanilla MB warband / original native and see how much it will speed up your game (and the compenstation of graphical quality)

如果你感觉DX７适合你的话，请继续读，因为维京征服默认是不允许DX7的（你可以选择DX７，但是一进入游戏他会强制选择DX9），这也是这个帖子的意义，告诉各位如何让维京征服接受DX7
If you feel like DX7 is your thing, please continue reading, because Viking Conquest Reforged does NOT allow DX7 by default (you can choose DX7, but once you enter the game it forces to DX9 anyways), this is also the purpose of this thread, let us know how to make Viking Conquest accept DX7.

正文1, 强制DX7 - Main1, force DX7

找到维京的文件夹（骑砍本身的文件夹-> Modules -> Viking Conquest），然后重命名/移动以下文件 &文件夹：
Find Viking Conquest's root folder (Mount blade's root folder -> Modules -> Viking Conuqest)， then rename / move away the following files & folders:
GLShaders
GLShadersOptimized
fx_configuration.h
mb.fx
postFX.fx
postFX.txt

然后将module.ini的 supports_directx_7 选项，由零改成 1
For, supports_directx_7 = 0 in module.ini, change it to supports_directx_7 = 1

最后，确认开始游戏时的“配置” -〉“图像” -〉“渲染方式” 一项是DX7，就可以开始游戏了。
Last, make sure the Configure-> Video -> Render Method option is set to DX7, then start the game.

进入游戏后，成功的话，你会发现整个地图变成雪白色，地上和海上都是白色，天上还有漂浮的黑色的长方形几何物体。
After entering the game, if success, you will note that the entire map becomes "frozen", that is, both the ground white and ocean is white, and there are black boxes floating in the sky.

在这种情况下，你会注意到游戏的已经变得比之前更流畅了，但是这个画质是在是不堪入目，因此请看正文2.
Right now you should noticed that the game is already having better performances than before, but this trade off (the graphic glitches) is really unbearable, so please read on.

正文2, 修正材质 - Main2, repair textures

这一步没什么好说的，因为写出来太麻烦，这是改好了的文件。请备份原文件然后把以下文件放到维京的资源文件夹里（骑砍本身的文件夹-> Modules -> Viking Conquest -> Resource 文件夹）
Not much to say here, because it's a pain in the rectal area to write out the whole thing, please just take the modified files and put it in Modules -> Viking Conquest -> Resource. Remeber to back the original files.

materials
http://pan.baidu.com/s/1slJxS09
pass 密码: ft1f

vc materials
http://pan.baidu.com/s/1mhFofhe
pass 密码: yxuw

两个文件放置完毕后，地图的水和草地就会回到原色了。至此游戏可以正常的在DX７模式下运行了。
After placing the two files, the map's water and ground will be back to their original color. At this point you will be able to play the game normally under DX7.

正文3, 减少战场人数 - Main 3, reduce battle size

维京把原版的人数设置直接翻了５倍，也就是说原版最低的３０人，到维京即使１５０人。
Viking Conquest multipled warband's battle size by a factor of 5, which means when the setting is 30 in warband, it becomes 150 in Viking Conquest.

在此感谢官方ＴＷ论坛的kalarhan同志。你可以按他说的去改，或者请下载这个文件，放到维京的Modules里边，记得备份原文件
Here thanks to Talesword forum's kalarhan. You can modify the file as he said, or download this file directly and put it in Modules. Remember to backup the original file.

mission templates
http://pan.baidu.com/s/1bGUzbK
pass 密码： 6m7y

结尾－结合以上，改到DX7并且降低战场人数五倍后，性能会毫无疑问的大幅上升，游戏会变得更流畅
Warping up above, changing to DX7 and decreasing the battle size by x5 will undoubtfully raise the game's performance and make it run much smoother.